BI-PARTING
HORIZONTAL SLIDING
POWER OPERATED DOOR "ADS-200"
White Metal Clad Finish
Diamond-Trac ® System
PowerTron ® Operator
Five Year Warranty
COOLER DOOR SPECIFICATIONS:
Supply where indicated on plans Jamison Mark
IV
™ Power Operated Bi-Parting Horizontal Sliding Cooler
Door, with Diamond-Trac ® System* and
PowerTron ® Operator.
Door leaves to have aluminum extruded structure
and
to be metal clad with #26 gauge white pre-painted
stucco embossed steel front and back.
Frame (casings and header) to be constructed of
aircraft quality aluminum extrusions with
white painted finish.
Door leaves to be filled with 4" (101.6mm) of Jamifoam
non-CFC
polyurethane insulation with an R value
of 28 at 40°F. Frame to
be insulated with
polystyrene inserts.
Door leaves to be equipped with low profile
pneumatic
reversing edge, effective full height and
full travel of door. Upon contact, door in closing
cycle is instantly reversed to open position.
Adjustable gasket at sides and head of frame
and
reversing edges cover gasket to be polyester reinforced;
door leaves to have sweep type
sill gasket.
Hardware to have protective coating against
corrosion.
Automatic opening to be provided with
two remote control, spring-cushioned, low voltage
pull switches.
Door power to be 208, 240 or 480 volt AC, 60
Hertz
(50 Hertz available), three phase. (ARCHITECT TO SPECIFY VOLTAGE.) PowerTron
® power operator to have
all gear drive, and all power controls to be
fully enclosed in NEMA 1 control boxes. Visible signal
light to show when motor is running. Complete
door assembly to be ready for connection to
power. (ARCHITECT TO DESIGNATE RESPONSIBILITY
FOR FIELD WIRING.)
FREEZER DOOR SPECIFICATIONS:
Freezer door specifications to be same as
cooler
door except for these substitutions and additions:
Supply where indicated on plans Jamison Mark
IV
™ Power Operated Bi-Parting Horizontal Sliding Freezer
Door with Diamond-Trac ® System* and
PowerTron ® Operator.
Provide Frostop heater cables in top, sides, lead
edges
and bottom of door. Complete device to be
assembled, ready for connection to 120 volt, 60
Hertz, single phase AC line (other voltages available).
SPECIAL NOTES:
Freezer Door is designed for installation in
warm
room with temperatures plus 33°F
(½°C) and above. If door
must be mounted in rooms
with temperatures of +32°F
(0°C) and below, contact BMIL
International.
When cold room temperature is below -2
0°F
(-29°C) and/or the
relative humidity is greater than 80%
on the warm side, Frostop heater cables
should be added to the frame/gasket assembly.
If the cold room temperature is below -4
0°F
(-40°C), or if the
temperature difference exceeds 90°F
(50°C), contact BMIL International.
OPTIONS: (SPECIFY which options are desired):
Metal cladding can be stainless steel,
stucco
aluminum, galvanized, or galvanized steel
painted to meet specifications.
If stainless steel construction, appropriate
hardware
components can be chrome plated
and/or stainless steel.
Padlocking provisions on front or back of
door
with safety release on opposite side. (Specify
which side with locking.) Safety release
feature permits door hardware to be
released, thus minimizing possibility of personnel
being locked in room.
6" (152.4mm) of insulation for freezer door (R value
42).
36" (914.4mm) pedestrian opening with automatic closing.
Electric eye or motion detector to protect
door
from truck passage.
Radio control operation from lift truck, 1, 2,
or
4 button.
Power components for connection to 120
volt
AC 60 Hertz, single phase (other voltages available).
Swinging wicket door.
Complete NEMA 3, 4, or 12 requirements.
Electrical reversing edge.
Dual Speed Operator
Hydraulic operator
M.I.D. Requirements
View windows: (contact factory for specific
recommendations.)
12" x 14" (304.8mm X 355.6mm) sealed glass unit.
a. Cooler Door - 2 layer 1" (25.4mm) thick
b. Freezer Door - 3 layer, 1" (25.4mm) thick with 120 V.A.C.
heat film (other voltages available).
